Alarm Wiring Question - Honda RC51 Forum : RC51 Motorcycle Forums
Reply
 
LinkBack Thread Tools Display Modes
post #1 of 12 (permalink) Old 08-28-2012, 08:13 PM Thread Starter
Member
 
2003rc51's Avatar
 
Join Date: Mar 2012
Location: North Carolina
Posts: 92
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Cool Alarm Wiring Question

I installed a small alarm on my rc a few weeks ago. In the area I am at I normally keep it in storage. But I am rebuilding the engine on my car, and while it was down I am keeping it at the house quite a bit more, as well as at work all day. And unfortunately I work in a not so nice neighborhood. So I grabbed a cheap alarm and installed it. But unfortunately I couldn't complete the whole installation. I wired the lights for flashing, the constant 12v, the acc circuit, ground, the shock sensor is built into the alarm computer. The few wires I cannot locate is:

Starter Wire Trigger - For Remote Start (not really necessary but might be nice)

Down Flameout Ignition Generator (I did find this wire up front, but I was wondering if anyone knows where it is or if it even is near the ecu area so I don't have to run wires all the way to the front and back.)

Up Flameout Ignition Switch (I also found this up front, but again, I don't want to have to run wires between up front and the rear. Also there is a gps tracker and silent alarm that was already installed up front.)

Thanks in advance for any help!
2003rc51 is offline  
Sponsored Links
Advertisement
 
post #2 of 12 (permalink) Old 08-28-2012, 10:48 PM
Lifetime Premium
 
MakisRC51's Avatar
 
Join Date: Jan 2012
Location: Korinthos, Greece
Posts: 3,239
Mentioned: 15 Post(s)
Quoted: 77 Post(s)
Could you please upload the alarm's wiring diagram?


My Öhlins Project: https://www.rc51forums.com/forums/showthread.php?t=6033
Quote:
Originally Posted by SubSailor View Post
Congratulation to MakisRC51 for winning the 2014 Bike Of The Year Contest!
MakisRC51 is offline  
post #3 of 12 (permalink) Old 08-28-2012, 10:58 PM Thread Starter
Member
 
2003rc51's Avatar
 
Join Date: Mar 2012
Location: North Carolina
Posts: 92
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Quote:
Originally Posted by MakisRC51 View Post
Could you please upload the alarm's wiring diagram?
sure, after we get done with dinner i'll scan it in.
2003rc51 is offline  
 
post #4 of 12 (permalink) Old 08-28-2012, 11:07 PM
Lifetime Premium
 
MakisRC51's Avatar
 
Join Date: Jan 2012
Location: Korinthos, Greece
Posts: 3,239
Mentioned: 15 Post(s)
Quoted: 77 Post(s)
Posting on the forum while eating dinner?


My Öhlins Project: https://www.rc51forums.com/forums/showthread.php?t=6033
Quote:
Originally Posted by SubSailor View Post
Congratulation to MakisRC51 for winning the 2014 Bike Of The Year Contest!
MakisRC51 is offline  
post #5 of 12 (permalink) Old 08-29-2012, 06:51 AM Thread Starter
Member
 
2003rc51's Avatar
 
Join Date: Mar 2012
Location: North Carolina
Posts: 92
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Welll, at the time I was in the middle of cooking it

But here is the diagram. Sorry about the quality, it is pretty crappy to begin with. Let me know if its not good enough I can scan it in at 600. But this is 300, I kinda doubt it gets much better than this. 300 is quite a lot for a document.

2003rc51 is offline  
post #6 of 12 (permalink) Old 08-29-2012, 09:18 AM
Lifetime Premium
 
MakisRC51's Avatar
 
Join Date: Jan 2012
Location: Korinthos, Greece
Posts: 3,239
Mentioned: 15 Post(s)
Quoted: 77 Post(s)
This diagram is not very helpful actually.
The way it names the wires doesn't help much.
However I think I've got a clue.....gotta ask though

Is this alarm model specific? Is this harness for the 2003 RC51?

Could you state make and model of the alarm?


My Öhlins Project: https://www.rc51forums.com/forums/showthread.php?t=6033
Quote:
Originally Posted by SubSailor View Post
Congratulation to MakisRC51 for winning the 2014 Bike Of The Year Contest!

Last edited by MakisRC51; 08-29-2012 at 01:04 PM.
MakisRC51 is offline  
post #7 of 12 (permalink) Old 08-29-2012, 03:28 PM Thread Starter
Member
 
2003rc51's Avatar
 
Join Date: Mar 2012
Location: North Carolina
Posts: 92
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
No its not model specific. Just for a motorcycle. Besides that its pretty generic....but I mean you can pretty much tell that from the diagram. I was running through an install with a 900rr, but it ended up being different on the signal wire. And I found the starter kill, flamout and kill switch ignition up front. But I would rather not run wires all the way to the front of the bike.
2003rc51 is offline  
post #8 of 12 (permalink) Old 08-30-2012, 01:06 AM
Lifetime Premium
 
MakisRC51's Avatar
 
Join Date: Jan 2012
Location: Korinthos, Greece
Posts: 3,239
Mentioned: 15 Post(s)
Quoted: 77 Post(s)
Ok, here's how I would connect them to my bike.

Starter Wire Trigger - For Remote Start : splice the Yellow/Red wire on the starter relay coupling (the one with the 30A fuse on it) and attach it with some soldering paste. Don't cut the Yellow/Red wire though.

Then go to the Bank Angle Sensor's Relay. There's a Red/Orange wire. You cut it an inch away from the relay's coupling and you solder

Gray Down Flameout Ignition Generator: on the half that goes to the coupling
Pink Up Flameout Ignition Switch: on the half that goes towards the harness (eventually to the Bank Angle Sensor)

Before cutting this wire I would make a dummy extension of the relay's wires and test the connections through that to make sure it works fine.

Please don't use this piece of shit anywhere on your connections



My Öhlins Project: https://www.rc51forums.com/forums/showthread.php?t=6033
Quote:
Originally Posted by SubSailor View Post
Congratulation to MakisRC51 for winning the 2014 Bike Of The Year Contest!
MakisRC51 is offline  
post #9 of 12 (permalink) Old 08-30-2012, 02:11 AM Thread Starter
Member
 
2003rc51's Avatar
 
Join Date: Mar 2012
Location: North Carolina
Posts: 92
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
lol I never use butt connectors, twist connectors, or especially those connectors. I have been wiring for years. I solder, shrink wrap, and always use shielded wire. Then normally put plastic conduit style covers wrapped with electrical tape. And I'll look through all that tomorrow. Sounds like it could work perfectly! Thanks for the help. I'll let ya know how it goes.
2003rc51 is offline  
post #10 of 12 (permalink) Old 08-30-2012, 02:12 AM Thread Starter
Member
 
2003rc51's Avatar
 
Join Date: Mar 2012
Location: North Carolina
Posts: 92
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
I am wondering instead of the bank angle sensor wiring it in to the kickstand sensor. Thats at least how a lot of others are saying to wire it in. I doubt I have any issues with the bike ever being over far enough to activate the bank angle sensor. But I don't want to start the bike with remote start unless the kick stand is down. Or either the neutral safety switch or what not....I will do some looking around and see!
2003rc51 is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Honda RC51 Forum : RC51 Motorcycle Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome