DID Automotive timing chain? - Honda RC51 Forum : RC51 Motorcycle Forums
 
LinkBack Thread Tools Display Modes
post #1 of 4 (permalink) Old 07-24-2013, 03:22 PM Thread Starter
Senior Member
 
Join Date: May 2011
Location: Griffin, GA
Posts: 317
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
DID Automotive timing chain?

So im working on a Hyundai 4cyl cylinder head today, tore it down and upon inspection i noticed the cam chain has the some markings on it, it says DID 05S JAPAN, i was like WTF i knew they messed with some powersports timing chains but i just didn't think they were OEM for Hyundai, is this a real DID chain? lmk if you know anything about these.

04 Nicky
Jardine slip ons
520 conv. 15/40 RK quick accel kit
RickyBobbyv8 is offline  
Sponsored Links
Advertisement
 
post #2 of 4 (permalink) Old 07-24-2013, 03:33 PM
Senior Member
 
wingnutt's Avatar
 
Join Date: Nov 2012
Location: Maple Plain Mn.
Posts: 1,327
Mentioned: 3 Post(s)
Quoted: 58 Post(s)
Speciality
Chain Series
Roller Chains for
Power Transmission
Small Pitch Chain
The smallest chain complying to ANSI is DID25 of 6.35 mm pitch.
However, in response to the demands for smaller chains in
recent years for high technology machinery such as office
equipment, medical machines and industrial robots, we provide
DID15 of 4.7625 mm (3/16 inch) pitch and also DID15H1 as a
high-power version of DID15. These high precision chains are
manufactured under severe quality control especially required
for small sizes, taking wear resistance also into account.
Selection of chain
Refer to the "Low-speed selection" (P.121). However, the chain
operation speed can be set considerably high depending on the
type of lubrication as shown in the table below.
Connecting links and offset links
R connecting links are used for small pitch chains. However,
since their strength is lower than that of the base chain, and
since the clip is likely to come off in high speed operation, the
use of connecting links is not recommended. Use a loop chain
without attaching connecting links.
Offset links are available for chains other than DID15 and
DID15H1, but their use is not recommended for the same reason
as stated for the R Connecting links.
DID
15: A high precision
mini-pitch bushing chain
that is smaller than a
compact drive chain for
general applications,
DID25
DID
25: Smallest bushing
chain among ANSI
standard chains using
curl bushings.
DID
35: A ANSI standard
bushing chain suitable
for small precision
machines that require
high strength.
Approx.
weight
(k
g
/m)
Dimensions
Note: The values of max. allowable tension are not applied to connecting links.
Chain No.
DID 15
DID 15H
1
DID 25
DID 25H
DID 25T
DID 35
DID 35T
4.7625
4.7625
6.35
6.35
6.35
9.525
9.525
2.40
3.18
3.18
3.18
3.18
4.78
4.78
2.48
2.48
3.30
3.30
3.30
5.08
5.08
1.62
1.62
2.31
2.31
2.31
3.59
3.59
6.25
7.30
7.80
9.00
8.00
12.00
12.00
6.90
──
8.50
9.45
8.50
13.00
13.00
0.60
0.72
0.72
1.00
0.72
1.25
1.25
0.60
0.72
0.72
1.00
0.72
1.25
1.25
4.30
4.30
5.90
5.90
5.90
9.00
9.00
1.96
3.14
4.41
5.88
4.41
11.20
11.20
270
320
450
600
450
1,150
1,150
0.49
0.58
0.73
1.07
0.73
2.15
2.15
50
60
75
110
75
220
220
0.060
0.789
0.109
0.122
0.109
0.265
0.265
0.089
0.103
0.134
0.163
0.134
0.332
0.332
Width
W
Dia.
D
Dia. Length Thickness
d
Width
H
Pitch
PEFTt
Pin
Bushing Plate
Baring area
(cm
2

Avg. tensile
strength
kN
k
g
f
Max. allowable
load
kN
k
g
f
Unit (mm)
Roller Chains for Power Transmission
Specialty Chain Series
DID 15
DID 15H
1
DID 25
DID 25H
DID 25T
DID 35
DID 35T
Type
A
Oil feeder, brush, drip
Type
B
Oil bath, disk
Type
C
Forced pump feed
200
m/min or less
150

110

1200
m/min or less
1000

1
850

Over 1200m/min



Operating speed and type of lubrication
R connecting link

THIS IS JUST OFF THE TOP OF MY HEAD
wingnutt is offline  
post #3 of 4 (permalink) Old 07-24-2013, 05:40 PM
Senior Member
 
extrapolator's Avatar
 
Join Date: Apr 2013
Location: FL
Posts: 2,457
Mentioned: 11 Post(s)
Quoted: 99 Post(s)
Umyeah you put the NUT in wingnutt
extrapolator is offline  
 
post #4 of 4 (permalink) Old 07-25-2013, 09:30 AM Thread Starter
Senior Member
 
Join Date: May 2011
Location: Griffin, GA
Posts: 317
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
lol thanks for the info

04 Nicky
Jardine slip ons
520 conv. 15/40 RK quick accel kit
RickyBobbyv8 is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Honda RC51 Forum : RC51 Motorcycle Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome